2023-2024 Kia Telluride & 2023-2024 Hyundai Palisade – 2.0″ Front Lift Kit and 2.25″ Rear Lift Kit with Shock Shaft Extensions #306019

Code: 306019


In Stock


This Kit Fits:
2023-2024 Kia Telluride SUV 2WD & 4WD ~all models and trims EXCEPT the X-Line/X-Pro

~ the X-Line/X-Pro have a different suspension and trim package, there is more approach angle and the setup is different from a “normal” Telluride….if you have the X-Line/X-Pro package this Telluride kits will not work you will need kit #306020**

2023-2024 Hyundai Palisade SUV 2WD & 4WD – all models and trim levels

You have your shiny new Kia Telluride/Hyundai Palisade, you have it loaded up and your ready to hit the road, head to that killer campground down at the lake and you have your boat hooked up and ready to go or maybe you are heading to some amazing place up in the mountains, all the gear is loaded, your roof box has all the kids toys and mountain bikes are loaded on the hitch rack…all is great until you leave the pavement….quickly, your realize your killer new SUV sits WAAAAAY TO LOW in the front, way to low in the rear and your underbelly starts dragging….even worse, when you hook up your trailer or load your dirt bike on your hitch mount rack it sags….guess what, we have the solution, our  2.0″ front and 2.25″ rear lift kit will help lead the way to fix all those problems!

The 306019 is the kit most families who use there SUV as a daily driver will be happiest with, towing boats, trailers, hauling kids and going on adventures…be it the mall or your favorite campground!

**if you have the tow package and you do run your SUV loaded or you do tow, we suggest you use this kit # 306019 as it comes with a taller rear lift and the self levelling shock shaft extensions…if you are going off-road and you are NOT being fully loaded with people or “stuff”” and towing is NOT something you plan on doing – kit # 306021 is a more off-road based kit, this kit will give maximum ground clearance**

This kit has been designed specifically for the Telluride and the Palisade. This kit is the one we created for the perfect daily driver combination for the person who drives the vehicle daily, it runs around “with stuff” or “7/8 seaters full” most of the time, it is designed for when the SUV is either full of soccer gear and the kids and loaded for those weekly games or you have the trailer full of ATV’s and dirt bikes hooked up and you are headed out for family fun…for us, we figured this would be the “every person”…it is the most practical version in case you have the self levelling shock and can’t make a decision!

We have been selling this kit to Kia & Hyundai dealers around the world since it was released, this kit is designed to work WITH the stock parts that came on your vehicle, no need to modify any parts, we include everything you need to create the do anything Telluride/Palisade.

We have been doing this for a long time (we built our first unibody lift in 2005) and while we would LOVE to make it an even taller kit, we tried that already ~ our original design for the Telluride/Palisade was a 3″ kit and it was just too much – we didn’t like the angles and how it drove, while some people would be fine with it, we design every part we make to keep your vehicle driving and operating like stock; and do our best to make sure parts do not wear out any faster than they would without our kit installed. 

This kit will increase your front ground clearance and keep that air dam and bumper out of the mud or sand on those trips to the cabin or the beach, and yes, when you add a size or two taller tire you will get 2.0 -3.5″ MORE ground clearance depending on your tire and wheel choices.

This kit has been tested with full throttle, wheels sliding and basically…well doing things you should never do to a new vehicle…we DO NOT recommend beating on your vehicle, you will break parts :-}

This is a straightforward install, yes we do include some very important simple install tricks in the instructions – you just need to make sure to read the instructions, they are not campfire starter!

There is NO cutting or welding or permanent modifications needed. 

This  lift kit allows you to fit much more aggressive tires and wheels allowing your Telluride/Palisade to take the family and all your toys to where they need to go! 

***ALWAYS test fit wheels and tires AFTER lift install***

We have fit up to 265/60R18 tires on aftermarket wheels….make sure to send us pics so we can post them up and let people know what your choice was!

Note: Every wheel and tire company seems to use a different measuring tape, one companies 265/60R18 will be 30.5 inches tall and another may be 31.5” tall yet they have the same size on the sidewall – we can’t possibly test ALL combinations of wheels and tires so please install the kit before ordering tires or use an exact combination you have seen fit before!

All of our kits are a direct bolt in and require no modifications to your vehicle. These kits retain the stock ride quality of your truck as we use as many OEM parts as possible – keeping your truck under warranty is important, which is why we designed each kit to work with Factory parts..

Every Truxxx lift kit is made in the using USA or Canadian Mill Certified Steel and laser cut to precision tolerances using OEM drawings. 

Every kit is welded using the latest US Made welders and triple checked to ensure proper fitment. 

Each kit contains front strut spacers and sway bar extensions – we include all the all the required hardware in 10.9 & 12.9 grade, we have detailed instructions and complete alignment specs. 

Recommended installation time is approx. 3 hours + alignment and 31.0” tall tires are commonly used with a stock style offset wheel.


Additional information

Front Lift

Rear Lift




Vehicle Year



There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.